Heating consumption of buildings

Scope

To define heating consumption of buildings. D↷

Definition

Heating consumption (Q) of buildings can be defined with knowledge of surface area of building, inside and outside temperature in certain time period, and heat permeability factors. Easiest way to use heating consumption is to define it as floor area weighted calculation.

Assumptions:

Af = Ar
Aw = nAf
A = Af+Aw+Ar=(n+2)*Af

Buildings overall heat transfer coefficient per floor area is calculated as:

Uf = (Af/Af*Uf + Aw/Af*Uw + Ar/Af*Ur)/(A/Af)
=[(1/n)*Uf + n*Uw + (1/n)*Ur)]/(n+2)

where A_f is area of floor, A_r is area of roof, A_w is area of walls, A is area of building, which emits heat, n is number of floors in the building and U_f is the overall heat transfer coefficient of floor, U_w the overall heat transfer coefficient of walls, and U_r is the overall heat transfer coefficient of roof. Unit of areas are m², unit of the overall heat transfer coefficients are kW/(m² K).

Building overall heat transfer coefficients are regulated in Finnish building regulations, which are presented in following table

Part of building	1978-1985		1985-2002		2003-2006		2007-2010		2010-?
,	Mass less than	Mass over	Warm area	Half warm area	Warm area	Half warm area	Warm area	Half warm area	Warm area	Half warm area
,	100 kg / m2	100 kg / m2	> 17 °C	> 5 °C	> 17 °C	> 5 °C	> 17 °C	> 5 °C	> 17 °C	> 5 °C
,	[W / m2 K]	[W / m2 K]	[W / m2 K]	[W / m2 K]	[W / m2 K]	[W / m2 K]	[W / m2 K]	[W / m2 K]	[W / m2 K]	[W / m2 K]
Walls	0,29	0,35	0,28	0,45	0,25	0,45	0,24	0,38	0,17	0,26
Roof	0,23	0,29	0,22	0,45	0,16	0,45	0,15	0,28	0,09	0,14
Floor	0,23	0,29	0,22	0,45	0,16	0,45	0,15	0,28	0,09	0,26
Part which is against ground	0,4	0,4	0,36	0,45	0,25	0,45	0,24	0,34	0,16	0,24
Window			2,1	3,1	1,4	2,1	1,4	1,8	1	1,4
Door			0,7	2,9	1,4	2,1	1,4	1,8	1	1,4

Heating consumptions of building is calculated as:

Q = Uf * Af * (Tin-Tout)dt

where U_f is floor weighted overall heat transfer coefficient per floor area of building, A_f is area of floor, and T_in is inside temperature and T_out outside temperature in time dt.Unit of areas are m², unit of heating permeability factors are kW/(m² K).

Buildings also need thermal energy for warm tap water. This can be calculated by a following function

Qw = cp,w pw qm,w * (Twarm - Tcold )t

where Q_w is thermal energy which is needed to heat tap water, c_p,w is specific thermal capacity of water, p_w is density of water, q_m,w is volume of needed warn tap water, T_warm is temperature, where the tap water is heated, T_cold is temperature of the cold water and t is time. This can be also estimated by looking buildings thermal energy consumption in summer months, when there can be estimated to be only warm tap water use, because of outdoor temperature.

Unit

kW/year D↷